Back to Indoors

Moderators: BryanDelMonte, SEPGRS-Officers

Back to Indoors

Postby BryanDelMonte » Sun Oct 09, 2011 11:47 am

While I like occasionally running outdoors in the snow during winter (see my Youtube videos here), I plan on setting my Sievers workbench back up to elevate my basement floor layout of Aristo-Craft US track. I will post a pictures here when I return to this project in a few months.

Any other pictures of indoor layouts are, of course, welcome in this forum.

Bryan Del Monte
BryanDelMonte
Brakeman
 
Posts: 180
Joined: Mon Mar 28, 2011 7:26 am
Location: West Chester, PA

Re: Back to Indoors

Postby Steve Kilpatrick » Sat Nov 05, 2011 12:08 am

This winter I’m hoping to create several buildings for my garden RR and possibly build an engine to run at PLS next summer. I hope to have an indoor layout someday and was wondering if you would welcome a visit to your indoor layout as it is being constructed? Steve Kilpatrick
Steve Kilpatrick
Hobo
 
Posts: 4
Joined: Fri Nov 04, 2011 11:47 pm

Re: Back to Indoors

Postby BryanDelMonte » Mon Nov 07, 2011 8:28 pm

Steve, I also have several buildings, all Pola, to build this Winter for my home GRR. I have most of the parts not machined (no mill yet) for the frame of ride-behind electric diesel engine 7 1/4" gauge to run at PLS, where I am a probationary member.

My Sievers benchwork will go up very quickly in an afternoon after I get the brackets for two overhead lights installed. You are welcome to visit with me after this initial setup planned for this month. Bryan
BryanDelMonte
Brakeman
 
Posts: 180
Joined: Mon Mar 28, 2011 7:26 am
Location: West Chester, PA

Re: Back to Indoors

Postby BryanDelMonte » Thu Dec 29, 2011 6:07 pm

This is what I assembled yesterday in approximately 1 hour with help from Colleen. Not a bad start...
Attachments
Bachmann Mogul Industrial DCC sound 004.jpg
Bachmann Mogul Industrial DCC sound 004.jpg (116.23 KiB) Viewed 4069 times
Bachmann Mogul Industrial DCC sound 003.jpg
Bachmann Mogul Industrial DCC sound 003.jpg (119.29 KiB) Viewed 4069 times
Bachmann Mogul Industrial DCC sound 002.jpg
Bachmann Mogul Industrial DCC sound 002.jpg (112.73 KiB) Viewed 4069 times
BryanDelMonte
Brakeman
 
Posts: 180
Joined: Mon Mar 28, 2011 7:26 am
Location: West Chester, PA

Re: Back to Indoors - Updates

Postby BryanDelMonte » Sun Jan 08, 2012 8:58 pm

More track was laid down, including a pass through siding.

I will next be replacing the manual AC switches with LGB electric switches left over from my prior layout and not needed outdoors.

I am going to try a automatic DC trolley line down the center of the layout running both DC and DCC.

Pulled out my LGB semaphore to install for signalling. It should also work with a recently purchased a Lenz BM-2 module for assymetrical automatic braking control (ABC) using my two engines with Zimo dound decoders and one with Zenx Gold decoder.
Attachments
Bachmann Lyn Zimo sound decoder 002.jpg
Bachmann Lyn Zimo sound decoder 002.jpg (106.43 KiB) Viewed 4052 times
Bachmann Lyn Zimo sound decoder 004.jpg
Bachmann Lyn Zimo sound decoder 004.jpg (113.13 KiB) Viewed 4052 times
Bachmann Lyn Zimo sound decoder 003.jpg
Bachmann Lyn Zimo sound decoder 003.jpg (114.11 KiB) Viewed 4052 times
BryanDelMonte
Brakeman
 
Posts: 180
Joined: Mon Mar 28, 2011 7:26 am
Location: West Chester, PA


Return to Indoor Layouts

Who is online

Users browsing this forum: No registered users and 1 guest

cron

x